|
Vmed
VacuPad
Surgical Support
Device with Dynamic Heat Control
 The
VacuPad is a flexible vacuum pad used as a surgical support device to support
and hold patients under anesthesia during and after surgical or diagnostic
procedures. VacuPads are designed specifically for animal surgery and can be
molded and formed to the patient when soft. When air is evacuated from inside
the pad, it becomes ridged and molds to the body shape, holding the patient
securely and comfortably in the desired position. Body heat loss leading to
hypothermia is a risk for all surgical patients and most often occurs with
smaller animals. Some studies show a reduced risk of infection if body heat is
maintained during and after surgery. The VacuPad contains Dynamic Heat Control
media which helps maintain body heat. A water circulating pad may be used on top
of the VacuPad.
Click on photos below to enlarge
Double click on the link below to download and save the VacuPad flyer on your
computer:
VacuPad Flyer.pdf
VacuPad
Key Benefits
- A superior method of supporting and holding patients under anesthesia.
- Helps maintain body heat.
- Holds patient securely and comfortably in the exact position desired for
procedure.
- Quick and easy to use.
- Easily cleaned and disinfected.
General Characteristics
- The VacuPad is available in two sizes. 24" x 16" for animals to 30
pounds; 36" x 23" for animals to 80 pounds. (Will partially support larger
animals)
- Inert to most chemicals. Hospital disinfectants can be used.
- The VacuPad is tough. Specially treated foam and two layers of reinforced
vinyl are used to provide the necessary durability and puncture resistance.
As with any pneumatic envelope, care should be taken not to cut or puncture
during use.
- Translucent to X-rays and compatible with MRI equipment. Valve is easily
identified as an artifact.
- Quick and easy evacuation. An efficient hand pump is available to
completely evacuate the pad with two or three strokes.
- Heavy duty, leak proof and finely controlled vacuum valve can be easily
opened to soften the pad in order to reposition the patient during procedure.
User Instructions
1. Pre-heat the soft VacuPad to 105° F for 30-60
minutes prior to use. Do not exceed 150° F. The
easiest method is to place an electric heating pad on the black surface of the
VacuPad. Remove the heating pad prior to use. The VacuPad can also be
pre-warmed using a heat lamp, oven, heated operating table or similar means.
Microwave ovens are not suitable. VacuPads store heat from the heat source and
conduct it to the patient for a period of 30-60 minutes.
2. Close valve on VacuPad; connect hose from hand pump.
3. Place VacuPad on operating table and place animal on VacuPad in the
position desired. Hand-form the pad around the patient and evacuate the air. Two
strokes will evacuate the small pad and 4-5 strokes will evacuate the large pad.
When the air is evacuated the pad becomes ridged and holds the animal in the
desired position. Approximately 15 cm HG vacuum is needed for best rigidity.
This is easily achieved using the VacuPump.
4. To release vacuum, open valve.
Cleaning, Repair and Warranty
Clean with soap and water. Dilute bleach and hospital disinfectants can be
used. VacuPads are made with two layers of heavy, nylon-reinforced vinyl and are
quite durable to scratch or cutting movements, but less durable to sharp
puncture forces. Punctures are effectively sealed with a piece of non-breathing
surgical tape or regular Scotch tape over the hole. The tape works well because
the vacuum draws the tape patch toward the puncture ensuring a tight seal with
each vacuum draw. Vinyl patch kits for larger holes can be purchased wherever
inflatable products are sold. VACUPADS ARE WARRANTED FOR ONE YEAR EXCLUDING
DAMAGE OR MISUSE.
WARNING: NEVER USE AN ELECTRIC HEATING PAD BETWEEN THE VACUPAD AND THE
PATIENT SINCE THIS COULD CAUSE SERIOUS BURNS TO THE PATIENT.
Phone 800 926-9622 to order
| 
